>> 返回主页 发新留言 首页:登陆:注册:精华:排行 版主 
讨论区方式查看 界面风格:  

ATMEGA88 fuse bit 回复  
帅哥
inkub
If RSTDISBL is set "0" then ATMEGA not read, erase.
SPI is block.
Need parallel programmer.
I need help with this problem.

regards

返回列表 [ 发表时间:2008-7-3 3:46:35 ] 编辑 管理 返上

Re:ATMEGA88 fuse bit 回复  
美眉
cm
This is the chip function itself.Once the RSTDISBL is set "0" ,then ATMEGA not read, erase.It must be programmed by parallel mode,the chip can resume.There is not any other way.
返回列表 [ 发表时间:2008-7-3 9:02:09 ] 编辑 管理 返上

Re:ATMEGA88 fuse bit 回复  
帅哥
inkub
Yes, but if you add programming for parallel VP980?
返回列表 [ 发表时间:2008-7-3 14:25:55 ] 编辑 管理 返上

Re:ATMEGA88 fuse bit 回复  
美眉
cm
Once the RSTDISBL is set "0"by ISP mode,the chip didn"t be read, erase by ISP mode.It must be erased by parallel mode,the chip can resume.In the parallel mode,there are many pin to be used.After the chip resuming,the chip can be programmed by ISP mode again.There is not any other way.VP-980 can support parallel mode to programme this chip.In the chip list,the chips,there is not brackets(ISP) behind the chips name,is parallel mode.
返回列表 [ 发表时间:2008-7-3 15:50:27 ] 编辑 管理 返上

Re:ATMEGA88 fuse bit 回复  
帅哥
inkub
"VP-980 can support parallel mode to programme this chip"

Maybe add support for serial programming ATMEGA88 ?

返回列表 [ 发表时间:2008-7-3 16:49:14 ] 编辑 管理 返上

Re:ATMEGA88 fuse bit 回复  
美眉
cm
VP-980 can support two programmer mode,one is parallel mode,the other is ISP series mode.The pin that parallel mode is different from the pin that series mode.So,you must rejigger the RSTDISBL "1" by parallerl mode.
返回列表 [ 发表时间:2008-7-7 9:00:53 ] 编辑 管理 返上
共有回复 5 个,共 1 留言首页 前一页 下一页[1]

::: 您 可 以 在 此 直 接 回 复 当 前 主 题 :::
发 言 标 题: *(标题限制 40 个字符以内)
发  表  人: *(名字限制 10 个字符以内)
密   码: *(第一次留言自动注册)
验  证  码: * 0954
性   别: 女 (已注册用户不用填)
头   像: (已注册用户不用选)
电 子 邮 件:
  Q Q  : ICQ MSN
主 页 地 址:
选 择 表 情:
Ubb标签:
Q 帖图: Q帖图一  Q帖图二  Q帖图三




            (Ctrl+Enter提交)
网站首页 | 联系我们 | 关于我们

天津威磊电子技术有限公司

62.99 ms